Finding the Radio S/N for Dodge
The first step is finding the radio serial number.
Many drivers assume the code depends on the Dodge model or year, but in reality, the whole process relies on the unique radio unit's serial number.
Each radio has its own serial tied to the security system.
This is even better, because if you have bought a used radio, the VIN or other vehicle-specific data wouldn't help.
Based on the radio version used, you may be able to retrieve the serial directly from the screen or by looking at the label on the radio chassis.
Fast Serial Lookup Using Radio Controls
Try the following for your 2013 Dodge Avenger:
The 2013 Dodge Avenger front-wheel-drive sedan from this era may feature a MyGIG radio (RER 730N) or an first-generation Uconnect system fitted in the sedan's center stack. These pre-2014 head units do not support on-screen serial display.
The serial number can only be accessed by pulling the radio from the Avenger's center stack and reading the barcode label on the unit casing.
View the Serial by Pulling Out the Unit
If the serial number cannot be accessed on-screen, use the removal method.
Most Dodge Avenger original radios include a tag with the serial number printed on the chassis.
Step-by-Step Approach:
- Turn off the vehicle.
- Lift the trim surrounding the radio.
- Loosen the fasteners.
- Slide the unit outward to access the label.
The serial number is usually located near the manufacturer sticker.
To access the serial on the 2013 Avenger's radio, you'll need to remove it from the dash:
- Turn off the vehicle.
- Carefully remove the center trim panel around the radio. The Avenger's sedan trim panel releases with friction clips – start at the bottom.
- Remove the four Torx T20 mounting screws holding the radio.
- Slide the unit forward and locate the serial label on the top, side, or back of the radio.
Take care with the wiring harness. You don't have to disconnect it unless absolutely necessary.
Example: Dodge Avenger serial number label location
Typical Radio Serial Prefixes and Formats
Common radio units in the 2013 Dodge Avenger and their serial formats:
- MyGIG REP 430 (non-nav touchscreen) – Serial prefix:
TM9 - MyGIG RBZ 430 (6.5" touchscreen) – Serial prefix:
TM9orT00AM - MyGIG RER 730N (navigation) – Serial prefix:
TM9 - RES 130 (base CD/MP3) – Serial prefix:
TM9orT00AM
All serials are 14 characters. Be sure to use the serial number, not the part number (P05064... or 68...).
Entering Your Unlock Code
After generating the correct unlock code based on the S/N, you can restore normal functionality by entering it into the unit.
The code entry process depends on the radio interface, but most 2013 Avenger systems follow a similar structure using preset buttons, touch controls, or rotary knobs - depending on if it's a factory or an aftermarket unit.
You will typically see SAFE displayed on screen.
Entering Process
To input the unlock code on the 2013 Avenger's radio:
- Turn ignition to ON. The radio displays "CODE" or "ENTER CODE".
- Touchscreen models (REP/RBZ/RER): Tap the touchscreen number pad to enter each digit.
- Non-touchscreen models (RES/REF): Press preset button 1 repeatedly for the first digit, button 2 for the second, 3 for the third, 4 for the fourth. Hold Enter/OK to confirm.
Warning: 3+ wrong attempts trigger a lockout. Keep the Avenger's radio powered for about 60 minutes to clear it.
From Serial Number to Unlock Code for your Dodge Avenger - Explained
- Rather than relying on Dodge dealership lookup or online threads you can generate the code online using the radio S/N.
- Identify your radio's serial. It is always present on the unit itself, and sometimes you can see it on the Avenger's radio screen.
- Type it into the generator above, and the system will retrieve the correct 2013 Avenger unlock code.
- When you receive the code, type it in using Avenger's radio controls to release the blockade fully.
- The entire process takes just a short moment and requires no VIN, documents, or technical knowledge.
Why Is the Radio Asking for a Code?
2011–2014 Avenger owners face this primarily due to:
- Battery disconnect or replacement — the primary cause on pre-2014 Avengers.
- Aging battery failure — older Dodge sedans are prone to dead batteries which trigger the lock.
- Blown fuse — fuse failure also counts as a power loss.
- Used purchase — second-hand purchase without documentation often means the code was never recorded.
The unlock code is tied to the radio serial and does not expire.
Fixing Common Code Entry Problems for 2013 Avenger
When no "CODE" screen appears after a battery event:
- Confirm the ignition is in ON (not ACC) and wait 15–20 seconds to power up.
- Check the radio fuse — a blown fuse stops the radio.
- On some older units, pressing the power button on the radio face can wake the code prompt.
If the radio stays dark, power issue is the first thing to check.
After three wrong codes on the Avenger's early Uconnect, a 60-minute lockout activates. The display will present "WAIT":
- Keep the radio powered — key must stay in ON, engine off is fine.
- Wait the full 60 minutes.
- Cycling the ignition restarts the wait.
After the 60 minutes, try the verified code again.
A rejected code on the Avenger's MyGIG almost always means a serial number mismatch. The label has both a serial number (TM9 or T00AM, 14 characters) and a part number (P05064... or 68...) — only the serial generates the code.
Look at the sticker again and reach out for a free re-check if needed.
How you enter the code on the Avenger depends on which radio is fitted:
- Touchscreen models (MyGIG REP 430, RBZ, RER 730N) — Use the on-screen number pad. The display confirms each digit.
- Non-touchscreen models (RES 130, REF) — Press preset button 1 cycling to set the first digit, button 2 for the second, 3 for the third, 4 for the fourth. Press and hold Enter/OK to submit.
Not sure of your radio: a touchscreen means touchscreen entry; a non-touch face means preset buttons.
The Avenger's MyGIG radio requires physical removal to read the serial label. On the label:
- Serial number — 14 characters, beginning with
TM9orT00AM. Submit this. - Part number — starts with
P05064or68. Not needed.
Copy all 14 characters carefully — similar-looking characters are easy to mix up on older stickers.