Retreat Chrysler Voyager 2012 Radio Code With Radio S/N

Radio showing SAFE? Your Chrysler Voyager 2012 can be unlocked quickly using the radio unit's serial. Enter it in the form and use the steps below if you need guidance.

Most Voyager codes are delivered instantly.
Manual lookup may take a bit longer (full day).

We offer a full refund if the code doesn't work.
A proof that the code failed may be required.
Review our Refund Policy for complete terms.

Serial Number Patterns:

Your radio serial may start with: T00AM, T00BE, TM9, T0MYD, A2C, TQN, TVPQN, T0071, T00AD

Serial Number Examples:

T0MYD164822563 (T0MYD)
T00BE351823197 (T00BE)
TM9341100221 (TM9)
Dealer price $120 92% Off!
Our price: only $19.99
Secure Payment
Get Code Instantly
268+ Reviews
See reviews →
Guaranteed refund if the code is invalid
Chrysler Voyager 2012 car photo
How to find Chrysler Voyager 2012 radio serial number

Steps to Unlock Your 2012 Chrysler Voyager Radio

  • Instead of contacting Chrysler dealer or searching forums you can retrieve the code online using the radio S/N.
  • Identify the serial number. You will always find it on the unit itself, and in some cases you can see it on the Voyager's display.
  • Type it into the form above, and the software will identify the correct 2012 Voyager unlock code.
  • After receiving your code, type it in using Voyager's radio controls to unlock the system successfully.
  • The entire process takes only a few minutes and requires zero paperwork and no dealer visit.

How Code Entry Works on Your Chrysler Radio

Once the system gives you 2012 Chrysler Voyager anti-theft code from the S/N, you're ready to reactivate the radio.

Many drivers hesitate at this stage because input methods can look different across radio versions, but it's usually easy.

When the radio shows dashed lines, it means the unit is waiting for the correct numbers.

Step-by-Step - Correct Entering Process

To unlock the 2012 Chrysler Voyager Uconnect 4.3":

  1. Turn ignition to ON. Screen shows "ENTER CODE".
  2. Tap each digit of your 4-digit code on the touchscreen keypad.
  3. Radio auto-confirms after the 4th digit.

3 wrong attempts trigger a 60-minute lockout. Keep ignition ON. Switching off restarts the timer.

Entering Process Explained

After retrieving the unlock code for a 2012 Voyager radio, the digits can be entered straight at the head unit - no scan tool or dealer visit is required.

  • Limited attempts: Mopar head units only accept a small number of incorrect tries (commonly three) before going into a long lockout/WAIT state, so verify each digit before pressing it.
  • Turn the ignition to RUN/ACC so the radio powers up while the engine stays off.
  • Wait for the display to show CODE, Enter Anti-Theft Code, or a similar prompt.
  • On the RBZ/RHB/RHW MyGIG (6.5-inch) units, key in the digits using the on-screen number pad; on the base RES head unit, press the numbered preset buttons (1-6) in sequence.
  • Confirm the entry with the on-screen OK/Enter button on the MyGIG units, or with the tune/menu knob (or labelled enter button) on the RES.
  • If WAIT or a similar timeout appears after the failed-attempt limit is reached, leave the radio powered with the ignition in RUN for a continuous 30 minutes before trying the correct code again.

Can't Find Your Unit's S/N? Follow The Steps Below for Chrysler Voyager 2012

The first part is to find and write down the radio's S/N.

Based on the head unit type fitted in your 2012 Voyager, the S/N can usually be accessed either through the screen menu or by pulling the unit out and checking the label on the radio itself.

Follow the steps below to identify your serial quickly.

2012 Voyager - Which Radio Did You Get?

For 2012 the export Voyager continued unchanged on the RT minivan platform - mechanically the same vehicle as the North American Town & Country and Dodge Grand Caravan, sold as Chrysler Voyager in Canada and the UK and as Lancia Voyager across most of continental Europe. No Uconnect 8.4 RA3/RA4 - the dash kept the same legacy Mopar trio. Identify yours by the bullets below:

  • RES - Media Center 130 (base AM/FM/CD). Non-touchscreen unit with a small one-line display, physical hard preset buttons and large rotary knobs. No NAV button, no factory Bluetooth, no SiriusXM out of the box on most builds. Common on entry trims.
  • RBZ - Media Center 430 MyGIG (6.5" touchscreen, no nav). 6.5-inch color touchscreen with hard keys for Radio, Media, Controls, More and Phone flanking the screen. No NAV soft key on the home menu because it has no navigation hardware. The volume touchscreen option on mid trims.
  • RHB - Media Center 430N MyGIG (6.5" with Garmin nav, NA market). Visually identical bezel to the RBZ, same Mitsubishi-built 6.5-inch touchscreen and same hard buttons. Difference is on-screen: a NAV soft key on the home menu, a Garmin logo at boot and a 28GB internal hard drive for stored music.
  • RHW - MyGIG 430N export navigation. European-market high-line MyGIG navigation head unit cited in Lancia/Chrysler Voyager parts and aftermarket interface listings; outwardly similar to RHB but with European mapping and market-specific tuners.
  • Optional rear-seat DVD entertainment. 9-inch flip-down overhead screen with its own DVD player in the lower dash and wireless IR headphones; recognised by the headliner-mounted screen and independent of the head unit.

Using Hidden Radio Menus to Find the Serial

The method for 2012 Chrysler Voyager is this:

The 2012 Chrysler Voyager — Chrysler's entry-level minivan — came with the Uconnect 4.3" (RA2) on base trims. The 4.3" unit does not support on-screen serial access.

The serial number is only accessible from the label on the radio chassis after removing the unit from the minivan dash.

Access the S/N by Pulling Out the Unit

If the serial number cannot be accessed on-screen, use the removal method.

Most Chrysler Voyager original radios include a tag with the serial number printed on the housing.

Basic process:

  • Shut down the car.
  • Carefully remove surrounding dashboard trim.
  • Loosen screws holding the radio.
  • Pull forward to inspect the label.

Remove the 4.3" Uconnect from the 2012 Chrysler Voyager's practical dashboard:

  1. Switch off the vehicle.
  2. Remove the center bezel with a plastic trim tool.
  3. Remove the 4 Phillips mounting screws.
  4. Slide the unit out to read the serial label. The 4.3" unit is lightweight and compact.

Voyager's Hardware Label Method

The factory radios offered on the 2012 Voyager - typically the RES single-CD head unit, the RBZ MyGIG 430 (6.5-inch touchscreen), the RHB / RHW MyGIG 430N (6.5-inch touchscreen with navigation), and the optional REZ rear-seat DVD entertainment module - all carry their serial number on a printed chassis label. Because these legacy units do not expose the serial through the touchscreen, the head unit needs to come out so the sticker on the case can be read.

  • Safety first: switch the ignition off, remove the key, disconnect the negative battery terminal, and wait several minutes before touching wiring; never disturb the yellow airbag/SRS connectors and use plastic trim tools so nothing shorts or breaks.
  • Tools you will need: plastic trim removal kit, Phillips screwdriver, small Torx bit set, flashlight, and a 7 mm socket on hand if any retaining bolts need backing out further into the dash.
  • Ease the centre dash bezel forward at the lower edge using a plastic trim tool and work up the sides; on the RT minivan dash it is held in by four friction clips with no visible screws on the bezel itself.
  • Once the four clips release, set the bezel aside on a soft cloth - on this body it does not need to be unplugged from any harness to do the job.
  • Remove the four screws securing the radio chassis to the dash bracket.
  • Slide the radio forward and unplug the antenna lead and the multi-pin power/data connectors on the rear of the unit.
  • The serial number is printed on a barcode/sticker label on the top or side of the radio chassis, next to the part number and supplier markings; on the optional REZ rear-seat DVD module, the same kind of label sits on the unit's case.
  • Photograph the label up close and double-check ambiguous characters such as 0/O and 1/I before submitting the serial.
Chrysler Voyager 2012 radio serial number label location

Example: Chrysler Voyager serial number label location

Typical Serial Number Formats for 2012 Voyager Radios

Year Chrysler Voyager 4.3" Uconnect serial patterns:

  • TM9 – Found on early Harman RA2 units in the Voyager
  • T00AM – Typical Harman RA1/RA2
  • T00BE – Continental variant

Serial is 14 alphanumeric characters. Ignore the part number (starts with P or 68).

Common S/N Formats Used on 2012 Voyager Units

The factory radios fitted to the 2012 Voyager are legacy Mopar head units rather than the later Uconnect 8.4 platform, so the prefix on the chassis label depends on which head unit was specified and which supplier built it.

RBZ MyGIG 430 and RHB / RHW MyGIG 430N

  • These Mitsubishi-built MyGIG head units typically print an alphanumeric serial on the case sticker.
  • Common Mopar/MyGIG prefixes seen on this generation include TM9 alongside other T-style codes.
  • The serial is usually a continuous run of letters and digits with no dashes or spaces.

RES (single-CD)

  • The base RES head unit usually carries a Mopar-style serial on a chassis sticker.
  • Treat the printed label on the unit itself as the authoritative reference and copy each character exactly.

REZ rear-seat DVD module

  • The optional REZ overhead DVD entertainment unit also wears a printed chassis label with its own serial.
  • If codes are needed for that module, transcribe its serial separately and avoid guessing unclear characters.

Understanding Unlock Issues with Your Voyager

The Voyager 4.3" label has both serial and part number. Serial: 14 chars starting with TM9, T00AM, or T00BE. Part number (skip): starts with P or 68.

Double-check carefully. Contact support for a free re-check if needed.

The Voyager 4.3" uses touchscreen-only code entry. Press each digit on the on-screen keypad. Auto-unlocks after the 4th digit.

If no code prompt appears, the lock hasn't fired. Trigger it: briefly disconnect the battery, reconnect, turn ignition to ON.

On the Voyager 4.3" label: serial = 14 chars starting with TM9, T00AM, or T00BE. Part number starts with P or 68 — not the serial.

3 wrong entries lock the Voyager 4.3" for 60 minutes. Keep ignition in ON or ACC. Cutting power restarts the timer.

What Caused the Radio to Lock?

The 2012 Chrysler Voyager 4.3" Uconnect self-locks after battery is disconnected. The lock applies to all Uconnect minivans.

Causes: battery replacement, failed fuse, buying used without a code, or battery drained from storage.

Code comes from the radio serial number — not the VIN.

Get Your Chrysler Voyager 2012 Radio Code Now