Locate the Serial Number Needed to Generate Dodge Charger 2015 Radio Code
Very useful thing to know is that factory radios use a specific serial number to identify each unit.
The anti-theft system matches the code directly to the serial.
Different from car-specific data such as VIN or registration information, it is not determined by the model or production year, so you'll be able to generate it even if you have a radio that you installed afterwards.
Depending on the maker and radio installed in your Dodge Charger, the retrieval method varies.
Here are the most reliable ways to locate it.
Display-Based Serial Number Retrieval
These are the steps you need to follow for 2015 Dodge Charger:
The 2015 Dodge Charger is a performance muscle sedan and is equipped with the Uconnect 8.4" (RA3) touchscreen mounted prominently in the center console. The serial number is accessible directly on screen via Dealer Mode.
Climate Button Method:
- Turn the ignition to ACC or ON.
- On the Charger's center stack, the Climate Up, Climate Down, and Front Defrost buttons sit directly below the 8.4" screen. Press and hold all three simultaneously for 5 seconds.
- Dealer Mode opens on the display.
- Go to: System Info → Radio Part Info → Serial Number.
Alternative: Hold Temperature Up (red) and Temperature Down (blue) simultaneously for 5 seconds to enter Engineering Mode, then follow the same menu path.
Find the S/N by Pulling Out the Radio
If the serial number cannot be accessed via display, use the hardware method.
Most Dodge Charger OEM radios include a tag with the serial number printed on the chassis.
The process:
- Remove key from ignition.
- Carefully remove surrounding mounting frame.
- Remove fasteners holding the radio.
- Pull forward to inspect the label.
If Dealer Mode is unresponsive on your 2015 Dodge Charger, the radio must be removed to read the serial label. The Charger's driver-focused center stack has a single trim panel around both the radio and HVAC controls:
- Remove the center stack bezel – Work a trim tool along the perimeter of the bezel – the panel uses friction clips and typically releases from the bottom corners first.
- Remove the 4 Torx T20 screws – Located at the corners of the radio mounting frame.
- Slide the radio forward – Ease the unit out enough to expose the serial label on the side or top surface.
The serial is on a barcode sticker: a 14-character alphanumeric code. The wiring harness can stay connected while you note it.
Example: Dodge Charger serial number label location
Standard Serial Number Patterns on This Radio
The 2015 Dodge Charger Uconnect 8.4" radio is made by Harman or Continental. Typical serial number prefixes:
T00AM– Harman VP2 Uconnect 8.4" (most common format)T00BE– Continental Uconnect 8.4" variantTM9– Earlier Harman production units
Radio model designations for the 2015 Charger: RA3 (standard 8.4"), VP2 (8.4" with Beats audio). Example serial: T00AM394958584 (14 characters).
Reminder Don't confuse the part number (P05064... or 68...) with the serial number. Only the serial is needed for code retrieval.
Code Entry Process for 2015 Charger
After receiving 2015 Dodge Charger unlock code from the serial number, you're ready to reactivate the radio.
Some drivers hesitate at this stage because input methods can look different across radio versions, but it's usually simple.
When the radio shows CODE, it means the unit is waiting for the correct numbers.
Step-by-Step - Correct Entering Process
To enter the unlock code on the 2015 Dodge Charger's Uconnect 8.4":
- The screen displays "ENTER CODE" or ---- when the radio is locked.
- Tap the on-screen touchscreen keypad to enter each digit of the 4-digit code.
- After the 4th digit, the radio auto-confirms – no additional step is required.
Lockout: Three wrong attempts activate a 60-minute lockout. Keep the ignition ON for the entire lockout period. Turning off the ignition resets the timer.
Unlock Your 2015 Dodge Charger Radio in Minutes - How It Works
Vehicle radios use security codes tied to the radio unit itself instead of the model or production year.
- Our lookup service works by matching your Dodge Charger radio's serial number.
- After entering the serial into the form above, the system identifies the radio unit and generates the code that you need.
- Simply input the digits into the Charger stereo.
- This approach saves time compared to traditional methods for 2015 Dodge Charger.
Why Did the Radio Lock and Ask for a Code?
Charger owners experience radio lockouts most commonly because of:
- Battery work during performance mods — Owners who disconnect the battery for accessories, audio upgrades, or ECU work will encounter this after each disconnect.
- Seasonal storage and battery drain — Muscle sedans like the Charger that sit over winter can deplete enough to trigger the anti-theft.
- Routine battery replacement — any battery swap triggers the anti-theft.
- Used purchase without history — buying a used Charger without the unlock code means the radio is locked from the start.
Your Charger's unlock code is permanently tied to the RA3 serial number and does not expire.
Understanding Unlock Issues with Your Charger
Should the radio not ask for a code after a battery event, these steps may help:
- Turn the ignition fully to ON and allow a few seconds to boot.
- Check the radio fuse in the fuse box — a bad fuse can prevent the radio from powering on at all.
- Some Dodge vehicles require a brief button press on the touchscreen to wake the code entry prompt.
If the screen stays black, the fuse or a wiring issue is the most probable cause — consult the manual for the correct fuse.
The serial number label on Uconnect 8.4" radios contains several fields, and confusion is common. Use this guide to identify the correct one:
- Serial number — 14 alphanumeric characters, begins with
T00AM,T00BE, orTM9. This is the one you want. - Part number — begins with
P05064...or68.... This is not the serial.
The easiest approach on 2015-era Dodge Charger units is through Dealer Mode — it shows only the serial with no chance of confusion.
The Uconnect 8.4" (RA3/VP2) uses a touchscreen number pad exclusively for code entry — there are no physical preset buttons involved in this process. When the locked screen appears:
- Press each number on the touchscreen.
- The radio confirms the code after the 4th digit — no confirm step is needed.
If the touchscreen seems unresponsive, restart the radio by turning the ignition off and on and wait half a minute for the system to reload.
After entering three wrong codes, the Uconnect 8.4" triggers a 60-minute lockout and shows "WAIT" or "LOCKED" on screen. To clear the lockout:
- Leave the ignition ON — do not turn the car off.
- Wait for the entire hour.
- Turning off the ignition at any point resets the timer back to 60 minutes.
Once the lockout clears, try again carefully.
A typical cause for a rejected code is submitting a code tied to the wrong serial number. On Uconnect 8.4" radios, the label shows both the serial number (14 characters, starting with T00AM, T00BE, or TM9) and a part number (begins with P or 68) — only the serial is used for code generation.
If your code was rejected, re-read the serial from Dealer Mode or the label and contact support for a free re-check if anything looks off.