Can't Locate Your Unit's S/N? Follow The Steps Below for Jeep Wrangler 2013
The first part is to locate the radio's S/N.
Depending on the radio unit used in your 2013 Wrangler, the S/N can usually be accessed either through the display menu or by checking the label on the radio itself.
Below are the most common methods to identify your serial the right way.
Identify Your 2013 Wrangler's Factory Radio
The 2013 Jeep Wrangler (JK) continued the same factory MyGIG-era radio line-up that had been in place since the 2011 refresh. All units share the Mopar anti-theft code architecture, so identifying yours simply tells you what hardware you are working with for serial retrieval and code entry.
RES (base AM/FM/CD/MP3): the standard non-touchscreen receiver fitted to base trims. Single-DIN style face, dot-matrix display, hard buttons for source and presets, and a CD/MP3 slot.
RBZ - MyGIG 430 (6.5" touchscreen, no nav): the mid-tier factory MyGIG with a 6.5-inch colour touchscreen, AM/FM/CD/DVD playback, optional SiriusXM, and Bluetooth/USB on later builds.
RHB - MyGIG 430N with Garmin navigation: the navigation-equipped 6.5-inch MyGIG with the Garmin nav engine and an onboard hard drive for media storage.
How to identify yours: the Mopar sales code (RES, RBZ, RHB) is typically printed on the lower-right corner of the radio face, near the auxiliary input jack. The Monroney window sticker, build sheet, and VIN report each list the radio's sales code as well.
Find the Serial Number on the Radio Display
The method for 2013 Jeep Wrangler is this:
The generation split is the main story for the Jeep Wrangler. JK and JL are fundamentally different vehicles with different radio systems — the method that works on one will not work on the other.
JK Wrangler (2007–2018) — Physical Removal Required
The JK used Uconnect 430N or 730N with physical preset buttons — no touchscreen, no Dealer Mode. Whether you're a daily driver or have the Wrangler as a trail rig, knowing this matters: if your battery disconnects on a trail, you'll need to remove the radio to read the serial label once you get home.
The serial number is on a label on the radio chassis. Pull the unit out and look at the top or side. See the removal guide below for JK-specific steps and videos.
JL Wrangler (2018+) — Tech Upgrade: On-Screen Methods Available
The JL brought a proper modern infotainment system. If your JL has the Uconnect 7": hold Temp Up + Temp Down for 5 seconds. The Engineering Menu opens. Navigate: System Info → Target Main Data → Serial Number.
If your JL has the Uconnect 8.4" NEW: press the bottom-left + bottom-right edges of the plastic bezel frame simultaneously until Dealer Mode opens. Navigate: System Info → Radio Part Info → Serial Number.
Note After 2020 software updates, some JL units have Dealer Mode restricted. If that's your situation, the physical removal method is the fallback.
Serial format: 14 characters, e.g. T00AM394958584.
Taking Out the Radio to Access the S/N on the Tag
If the serial does not appear in menu, the next step is checking the radio itself.
Many Jeep radios require physical access to the serial tag attached to the unit.
Common approach:
- Start by completely turning off the engine - pull the key out.
- Then detach the dashboard bezel.
- Next, unscrew the mounting points and slide the radio forward.
- Look for a factory sticker showing the serial number.
📹 Video Guide: Jeep Wrangler Radio Removal
Watch step-by-step tutorials for removing your Jeep Wrangler radio:
2018+ Wrangler JL
2021 Wrangler JL
Need a different Wrangler year or model? Search YouTube for more Wrangler tutorials
Written Instructions
Physical Radio Removal (if Dealer Mode is unavailable)
If the on-screen method is not available on your vehicle, the radio can be physically removed to access the serial number label on the top, side, or back of the unit:
- Remove the trim bezel – Gently remove the dashboard trim surrounding the radio using a plastic trim removal tool. The bezel is held by friction clips.
- Unscrew the mounting bolts – Remove the 4 mounting screws (usually Torx or Phillips) securing the radio to the dash frame.
- Slide the unit forward – Gently pull the radio out far enough to see the label. Do not disconnect the wiring harness unless necessary.
- Locate the serial number label – Locate a white or silver sticker with a barcode on the top or side of the unit. The serial number is a 14-character alphanumeric code (e.g.
T00AM394958584).
For step-by-step guidance with video tutorials for specific vehicles, see our Uconnect radio removal guide.
Wrangler's Hardware Label Method
On the 2013 Jeep Wrangler (JK), the dependable way to capture the radio's 14-character serial number is to release the head unit from the dash and read the manufacturer label on its chassis. The procedure is the same whether the Wrangler has the base RES receiver, the RBZ MyGIG 430, or the RHB MyGIG 430N with Garmin navigation.
Safety first. Turn the ignition fully off and remove the key. Disconnect the negative battery terminal and wait several minutes for SRS / airbag capacitors to discharge before working in the dash. Avoid yellow airbag wiring, and release every connector by its lock tab instead of tugging.
Tools to have on hand. A 7mm socket or nut driver, a #2 Phillips screwdriver, plastic pry/trim tools (or a tape-wrapped flat-blade screwdriver), a small parts tray, and a soft cloth or piece of painter's tape to protect the dash pad from accidental scuffs.
Removal overview. The JK Wrangler's centre stack uses the recognisable sport-utility design with body-coloured plastics and clip-retained trim. Begin with the HVAC control bezel directly below the radio - it is held only by spring clips, so insert a plastic trim tool at one of the lower edges and work it outward in small steps until each clip releases. Tilt the bezel forward and disconnect the climate-control connector(s). Next, work the radio bezel free; it too is clip-retained around its perimeter. With both bezels out of the way you will see the radio chassis secured to the dash subframe by four 7mm-head screws, typically one near each corner of the mounting cage. Remove all four, slide the unit straight out, and disconnect the locking antenna connector and the multi-pin electrical harness(es) at the back.
Where to find the S/N. The 14-character serial number, which commonly starts with the letter T, is printed on a white or silver manufacturer sticker on the top, side, or rear of the metal chassis, alongside a Mopar/Chrysler part number and barcode. Photograph it for a clean, zoomable copy and transcribe it carefully - the difference between zero and the letter O is easy to misread.
Tips. Set your trim tools against a strip of painter's tape on the dash to avoid scuffs; keep all bezel and chassis fasteners separated so screw lengths do not get mixed; if a clip stays behind in a dash hole, fish it out and re-seat it on the bezel before reinstallation.
Example: Jeep Wrangler serial number label location
Common S/N Formats Used on 2013 Wrangler Units
Your Jeep Wrangler 2013 radio serial number may start with:
T00AMT00BETM9T0MYDA2CTQNTVPQNT0071T00AD
Standard Serial Number Patterns on This Radio
Factory radios on the 2013 JK Wrangler use 14-character alphanumeric serials printed on the chassis label, alongside a Mopar/Chrysler part number. The exact prefix typically depends on which sales-code radio is fitted.
RES (Base AM/FM/CD/MP3): typically a 14-character alphanumeric serial that commonly begins with the letter T, followed by a family identifier and a production sequence on the chassis label.
RBZ - MyGIG 430 (no nav): commonly begins with T00-style prefixes such as T00AM or T00BE, with the remainder being digits to total 14 characters.
RHB - MyGIG 430N (Garmin navigation): commonly begins with TM9, followed by a numeric sequence to fill out the 14-character format. These units appear on Wranglers ordered with factory navigation.
What to ignore on the label: any S/N or SER prefix, dashes, spaces, and the barcode are formatting only - the value to submit is the contiguous 14-character alphanumeric serial. Capitalisation matters, and prefixes can vary slightly between production runs and supplier batches, so always verify the value as printed on the label.
Final Step - Enter the Radio Code
Now that you've found the S/N and generated the unlock code, the next part is entering it into your radio.
Jeep factory radios display a locked screen when ready for input.
The process is usually simple, but button layouts and confirmation methods may change depending on the radio version installed in your Wrangler.
The Correct Way to Enter It
📹 Video Guide: Entering Your Unlock Code
Watch this tutorial demonstrating how to enter the 4-digit unlock code on your Jeep Uconnect radio:
Search YouTube for more code entry videos
Step-by-Step Code Entry Instructions
To enter the unlock code on your Jeep Uconnect radio:
- Turn the ignition to the ON or ACC position (engine off is fine).
- The radio screen will display "ENTER CODE" or show four dashes (----).
- For touchscreen models (Uconnect 8.4" or 7" with touchscreen):
- Use the on-screen keypad to tap each digit of your 4-digit code.
- The code will appear on screen as you enter it.
- For button models (older Uconnect 430/730 systems):
- Use the preset buttons (1-4) to enter the code.
- Press button 1 repeatedly for the first digit (e.g., press 5 times for digit "5").
- Press button 2 repeatedly for the second digit.
- Press button 3 repeatedly for the third digit.
- Press button 4 repeatedly for the fourth digit.
- Press and hold the Enter button (usually the round center button) for several seconds to confirm.
- After entering all 4 digits correctly, the radio unlocks and should function normally.
Important Tip: Make sure you enter the code carefully. Three incorrect attempts will trigger a temporary lockout (see warning below).
Correct Entering Process
Once you have the correct 4-digit anti-theft code for your 2013 Wrangler's radio, entering it is straightforward, but you only get a limited number of attempts before the unit forces a cooldown.
Limited Attempt Warning: Mopar MyGIG units (and the RES base receiver) for the 2013 Wrangler typically allow up to three attempts to enter a valid 4-digit anti-theft code. After three successive invalid entries the radio enters a WAIT (LOCK) state and shows WAIT on the display. Recovery: leave the ignition in the RUN position with the radio powered for a continuous 30 minutes (you may drive the vehicle during this time); only then will the CODE prompt return for another set of attempts. Power-cycling during the wait generally resets the timer.
Power up. Turn the ignition to RUN or ACC and wait for the radio to finish booting and display the CODE / ENTER CODE prompt.
Entry on a MyGIG touchscreen (RBZ / RHB): use the on-screen numeric keypad to tap each of the four digits of your code in order. Once the fourth digit is in place, an OK / GO button becomes active. Tap it to submit; a correct code clears the prompt and returns the radio to normal operation, while an incorrect code is counted as one of your three attempts.
Entry on the base RES (single-CD) radio: with the ignition in RUN and the display showing CODE, use the station preset buttons (1-4) to dial each of the four digits, then press the labelled enter/OK button (or briefly hold the assigned preset, depending on the unit's labelling) to submit. The display returns to play mode when the code is accepted.
If the code is rejected: stop after the second failed attempt, re-verify the digits against your paperwork, and start a fresh entry from the first digit. It is much cheaper to take the 30-minute wait than to risk further escalation. Tap each touchscreen digit deliberately - rapid double-taps on the MyGIG screen can register an extra digit and inadvertently submit an incorrect entry.
Locked Wrangler Radio? Here's Exactly How to Get the Code
- Rather than relying on Jeep dealership lookup or online threads you can retrieve the code online with the radio S/N.
- Identify the serial number. The best place to search is on the unit itself, and in some cases you can see it on the Wrangler's display.
- Enter it into the form above, and the software will retrieve the correct 2013 Wrangler unlock code.
- After getting it, type it in using Wrangler's radio controls to unlock the system fully.
- The entire process takes only a few minutes and requires zero paperwork and no dealer visit.
Understanding Unlock Issues with Your Wrangler
Common issues:
- part number instead of serial
- missing characters
- Incorrect prefix
Messages like LOCKED mean too many attempts.
Solution:
- ignition ON
- radio active
- wait for unlock delay.
Look for missing confirm steps, wrong input methods, or disabled buttons during lockout.
Check:
- radio serial accuracy
- digit order
- correct confirmation button
Common mistakes:
- part number vs serial
- extra spaces or missing characters.
Possible causes:
- radio not locked yet
- incorrect mode
- display delay.
Restart the system and check again.